Skip to content
ClearTradeREPORT

Real reporting for the people who build, power and maintain America.

Rooftop Equipment Walk Pads: Protecting Membranes Without Blocking Drainage

How to specify rooftop walkway pads from manufacturer data sheets: membrane match, drainage gaps, seam clearance, service routes and warranty terms.

By ClearTrade Report Editorial Team · Published November 13, 2026 · 10 min read

Four-step framework showing how to specify rooftop walkway pads: match the membrane, leave drainage gaps, stay off seams and map the service route.
Credit: ClearTrade Report Editorial Team.

The evidence that helps you specify roof traffic protection is the roof membrane manufacturer’s own walkway product data sheet and installation detail, read alongside the roof warranty and the service instructions for each piece of rooftop equipment. Those documents give the matching product, attachment method, drainage gaps, seam clearances and required locations. The numbers are not the same from one manufacturer to the next, so the walkway should follow the detail for the roof system you actually have.

Evidence label: Documentation-based guide. ClearTrade Report Editorial Team checked documents from Carlisle SynTec, GAF, Elevate, Sika, Johns Manville, the National Roofing Contractors Association (NRCA), the International Code Council (ICC) and Carrier on November 13, 2026. No outside professional review was performed and nothing was tested. Companies named are documentation examples, not recommendations. This guide contains no affiliate links.

This guide covers membrane wear, drainage and access routes. Worker fall protection, anchors and guardrails are outside the scope of this guide.

Match the walkway to the membrane system

NRCA’s roofing glossary entry for “Walkways” describes them as “materials or accessories such as traffic mats or pavers installed on rooftop surfaces” used “to provide wearing surfaces for traffic and/or protect a roof system from damage resulting from rooftop traffic.” The same entry describes walkway areas as “High traffic and high-service-frequency areas on a rooftop,” “particularly those leading and adjacent to vents, hatches and heavy duty air-conditioning units.”

Manufacturers make walkway products for specific membranes. Carlisle says its Sure-Weld TPO Walkway Roll “is designed to protect the Sure-Weld TPO membrane.” GAF says its EverGuard TPO Walkway Roll “is designed for use with EverGuard® TPO single-ply membranes.” Sika describes Sarnatred-V as “a thermoplastic rolled-out, heat welded walkway” used “to protect the Sarnafil or Sikaplan membrane.”

Attachment also depends on the membrane. The thermoplastic (TPO and PVC) products above are heat welded. GAF says to “Heat weld EverGuard® TPO Walkway Roll to the roof membrane surface continuously around the walkway roll perimeter.” Carlisle’s TPO sheet says to “weld all four sides of the walkway material to the membrane.” For EPDM, Carlisle’s Sure-Seal EPDM Pressure-Sensitive Molded Walkway Pads are pressure-sensitive pads, and the sheet warns that “The adhesive on the back of the PS Molded Walkway Pad will not adhere to dusted or dirty surfaces.”

The roof’s attachment method can change the walkway detail, too. Sika gives separate steps for adhered roofs and mechanically attached roofs. Johns Manville’s JM PVC Walkpad sheet says: “On mechanically fastened systems, avoid installing over the disc.” Identify the membrane brand, type and attachment method from the warranty or closeout documents first.

Where manufacturers say walkways belong

Several data sheets say where walkways are required. Carlisle’s EPDM pad sheet says: “Walkways must be installed at all traffic concentration points (i.e., roof hatches, access doors, rooftop ladders, etc.)” “regardless of traffic frequency.” Both Carlisle sheets add: “Walkways must also be installed if regular maintenance (once a month or more) is necessary to service rooftop equipment.”

Elevate’s UltraPly TPO Walkway Pad technical information sheet (TIS 1527) says: “The walkway pad or acceptable paver is required at all access points (ladders, hatches, doorways, etc.)” It lists the pad for use “As a walkway system on roofs subjected to traffic more frequently than once per month.” GAF’s heat-welded walkway pad detail notes walkway pads are “REQUIRED AT ALL ROOF ACCESS POINTS.”

Some manufacturers also limit where walkways can go near roof edges. Carlisle’s TPO sheet says “walkway rolls should not be installed within 10′ (3m) of the roof perimeter,” and its EPDM sheet’s precautions say the pads “cannot be installed within 10′ (3 m) of the roof perimeter” in a sentence that also refers to Design “B” systems, so check which restrictions apply to your roof design.

Leave gaps so the walkway does not dam water

A continuous walkway can dam water on a low-slope roof. The data sheets call for gaps between pieces, but the amount varies:

  • Carlisle TPO: “Cut the Walkway Rolls into maximum 10′ lengths and position with a minimum 1″ gap between adjacent pieces to allow for water drainage.”
  • Carlisle EPDM: “Allow a 1″-wide (25 mm) gap between PS Walkway Pads.”
  • GAF TPO: “Rolls must be spaced at least six inches (152 mm) apart to allow for drainage.”
  • Elevate TPO: “Install the UltraPly TPO Walkway Pad in maximum 10′ (3 m) long sections” “with a space between each section to allow for proper drainage.”

Two documents also address water under or beside the walkway. Elevate says to fully weld each section’s perimeter “leaving one or two 1″ gaps in the weld at the low side of the pad to allow for the escape of inadvertent moisture,” and adds: “Position the pad so that it does not result in ponding water.” For mechanically attached roofs, Sika says to weld the Sarnatred-V perimeter “leaving intermittent weeps as needed of unwelded Sarnatred-V along the low side for drainage.”

If water already sits on the roof near equipment, sort out that problem before you add walkways that could make it worse. Our guide to evidence for low-slope roof ponding covers how to document standing water. On the layout, mark drains and flow direction so gaps and low-side weeps line up with where water needs to go.

Keep walkways off seams and flashings

Welded or adhered walkways are hard to remove, so manufacturers ask you to keep them clear of membrane seams. Carlisle’s TPO sheet says: “Cut the walkway so a 4″ minimum gap is created over any field splices.” It explains why: “Since the attachment of the walkway to the membrane is permanent, this will allow access to the field seams.” Carlisle’s EPDM sheet says to “Discontinue Walkways over field splices allowing a minimum 1″ (25 mm) gap.”

GAF’s detail reads: “DO NOT CROSS SEAMS WITH WALKWAY PADS 6″ (152 mm) OFF EACH SEAM.” Elevate says: “Avoid applying the walkway pad over UltraPly TPO membrane seams and detail flashings.” JM’s PVC sheet says to “Minimize installing over seams and membrane splices whenever possible.” Sika takes a different approach for Sarnatred-V: check existing seams that will be covered “with a rounded screwdriver” and “reweld any inconsistencies before the walkway installation.”

With seam clearances ranging from 1 inch to 6 inches, cite the specific manufacturer’s detail rather than a generic dimension.

Route from roof access to each unit’s service side

Start at each roof access point, such as hatches, doors and ladders, and run a path to every unit that gets regular service. At each unit, carry the walkway to the sides where the work happens, not just the nearest corner.

The equipment manual tells you where those sides are. Carrier’s installation instructions for its 48TC rooftop units (Catalog No. 48TC-4SI) say to “Select a location for the unit and its support system (curb or other) that provides for the minimum clearances required for safety.” That includes “service access below,” “around and above unit as specified in unit drawings.” The manual includes a service clearance drawing and a figure showing access panel locations. Use the figures for the exact model on your roof to place walkway in front of each service panel.

The mechanical code also speaks to the route. ICC’s CodeNotes on worker safety on roofs explains the 2021 International Mechanical Code provisions on access to rooftop equipment, including Section 306.5. It says such access “shall not require climbing over obstructions greater than 30 inches (762 mm) in height” “or walking on roofs having a slope greater than 4 units vertical in 12 units horizontal (33 percent slope).” The CodeNotes also covers ladders, level work platforms and guards, which are outside the scope of this guide.

Read the warranty language on roof traffic

Warranties can tie traffic damage coverage to walkways. GAF’s EverGuard System Pledge Roof Guarantee lists among its exclusions: “Traffic of any nature on the roof unless using GAF walkways applied” “in accordance with GAF published application instructions.” The same guarantee says: “Any equipment or material that impedes any inspection or repair must be removed at your expense.”

The walkway itself may not be covered. Carlisle’s TPO sheet says: “Walkway Rolls are a maintenance item and are not covered under the Carlisle membrane systems warranty.” Its EPDM sheet says the same about PS Molded Walkway Pads. Budget for replacing worn sections as routine maintenance.

These are examples. The terms of the warranty issued for your roof control.

Specification checklist and roof plan

Collect the evidence for each item below before the walkway is specified.

Specification itemWhere to find the answerExample from the documents checked
Walkway productMembrane manufacturer’s walkway data sheetCarlisle TPO roll “designed to protect the Sure-Weld TPO membrane”
Attachment methodWalkway data sheet and installation detailGAF: heat weld continuously around the perimeter. Carlisle EPDM: pressure-sensitive adhesive on a clean surface
Maximum piece lengthWalkway data sheetCarlisle TPO and Elevate TPO: maximum 10 feet
Gap between pieces for drainageWalkway data sheetCarlisle: 1 inch minimum. GAF: at least 6 inches
Weld gaps or weeps on the low sideWalkway data sheetElevate: one or two 1-inch weld gaps. Sika: intermittent unwelded weeps on mechanically attached roofs
Clearance from seamsInstallation detailCarlisle TPO: 4 inches. Carlisle EPDM: 1 inch. GAF: 6 inches
Edge restrictionWalkway data sheetCarlisle TPO: not within 10 feet of the roof perimeter. Carlisle EPDM: a similar 10-foot precaution; check which system designs it covers
Where walkways are requiredWalkway data sheet and detailAccess points such as hatches, doors and ladders. Carlisle: also where service is once a month or more
Service sides of each unitEquipment installation manualCarrier 48TC: service clearance drawing and access panel figure
Warranty conditions on trafficIssued roof warranty or guaranteeGAF: traffic excluded unless using GAF walkways per its instructions

Once the answers are in hand, draw the walkway layout on a roof plan. Show roof access points, each unit and its service sides, drains and flow direction, field seams if known, the walkway pieces with their gaps, and any edge zone the manufacturer excludes. Keep it with the roof warranty and give a copy to every service contractor. Update it when equipment is added, moved or replaced.

Know the limits of this guide

Nothing in this guide was tested or installed by ClearTrade Report. The figures come from the documents listed below as they read on November 13, 2026. Manufacturers revise data sheets, and the documents carry different dates: Carlisle’s TPO sheet is dated May 20, 2025, its EPDM sheet January 19, 2024, Elevate’s TIS 1527 October 14, 2026, Sika’s Sarnatred-V sheet February 2022, JM’s PVC sheet July 2023, and the Carrier manual shows an edition date of May 2009. The GAF detail shows an issue or revision date of November 11, 2020. The code material is ICC’s CodeNotes summary of the 2021 International Mechanical Code, not the full code text; your jurisdiction may use a different edition or local amendments. The roof manufacturer’s current detail, the issued warranty and your local authority having jurisdiction control your project.

Primary references checked November 13, 2026: Carlisle SynTec, “Sure-Weld TPO Walkway Rolls Product Data Sheet” (TPO-1015) and “Sure-Seal EPDM Pressure-Sensitive Molded Pads Product Data Sheet” (EPDM-1098); GAF, “EverGuard TPO Walkway Roll” (COMEG844), “Heat-Welded Walkway Pads” detail and “EverGuard System Pledge Roof Guarantee” (COMTS704); Elevate, “UltraPly TPO Walkway Pad” Technical Information Sheet (TIS 1527); Sika Corporation, “Sarnatred-V Product Data Sheet”; Johns Manville, “JM PVC Walkpad” (RS-8315); NRCA, Roofing Glossary entry “Walkways”; International Code Council, “CodeNotes: Worker Safety on Roofs and Elevated Structures”; Carrier, “48TC*D Single Package Rooftop Gas Heating/Electric Cooling Unit with NOVATION Coil, Installation Instructions” (48TC-4SI).

Frequently asked questions

Do roof walkway pads need gaps between them?

Yes, in the documents checked. Carlisle calls for a minimum 1-inch gap between pieces, GAF says its TPO walkway rolls must be spaced at least six inches apart for drainage, and Elevate says to leave a space between sections. Follow the detail from your own roof manufacturer, because the numbers differ.

Can I use any walkway pad on any roof membrane?

No. Walkway products are made for specific membrane systems, such as TPO, PVC or EPDM, and are heat welded or adhered according to that manufacturer’s instructions. Confirm the membrane brand, type and attachment method before choosing a walkway product.

Are walkway pads covered by the roof warranty?

It depends on the warranty. Carlisle says its walkway rolls and molded pads are maintenance items not covered under its membrane systems warranty. GAF’s System Pledge guarantee excludes traffic on the roof unless GAF walkways are applied per its instructions. Read the warranty issued for your roof.

Where should rooftop walkways go?

Manufacturer documents call for walkways at roof access points such as hatches, doors and ladders, and Carlisle also requires them where equipment is serviced once a month or more. Run the route from each access point to the service sides of each unit shown in the equipment manual, and record it on a roof plan.

Disclaimer: This guide is general information based on manufacturer, trade association and code organization documents, not professional roofing, engineering, warranty or legal advice for a specific building or product. Follow the current installation details and warranty for your roof system and the requirements of your local authority having jurisdiction. AI tools assisted with drafting. ClearTrade Report Editorial Team checked the cited sources and edited this guide.

Need a qualified professional?

Trusted Pros uses visible license-verification states and never ranks paid listings above unpaid listings.

Explore Trusted Pros