A spot voltage reading tells you what the voltage was for the few seconds someone held the leads on it. Intermittent equipment problems usually need a recording instead: an instrument left connected for days or weeks that logs trends and captures events when a set threshold is crossed. To scope a useful investigation, decide which disturbances to capture (sags, swells, interruptions, transients, harmonics, flicker, unbalance and, where relevant, neutral-to-ground voltage), where to connect, how long to record, and what trigger thresholds to use. Keep your own time-stamped log of equipment problems during the recording. Then judge the report on whether each event comes back with a time, magnitude, duration and waveform that can be matched to your log.
Evidence label: Documentation-based guide. ClearTrade Report Editorial Team checked documents from Hydro One, IEEE Standards Association, the International Electrotechnical Commission (IEC), Fluke, Hioki and Dranetz on November 17, 2026. No outside professional review was performed and nothing was tested. Companies named are documentation examples, not recommendations. This guide contains no affiliate links.
Why a spot reading is not a recording
A handheld multimeter is a troubleshooting tool, not a power quality recorder. Fluke’s 1587 FC Insulation Multimeter page says the meter “Measures ac/dc voltage, dc millivolts, ac/dc milliamps, resistance, and continuity” and includes “min/max” among its functions. The page makes no power quality claims for the meter, and it does not describe triggered event capture or waveform recording.
Power quality monitoring is a defined practice with its own reference documents. The IEEE Standards Association page for IEEE 1159-2019, IEEE Recommended Practice for Monitoring Electric Power Quality, lists it as an “Active Standard.” Its abstract says it “includes consistent descriptions of conducted electromagnetic phenomena occurring on power systems.”
Hydro One’s Power Quality Reference Guide for Customers and Utility Representatives describes the instruments built for this job: “Disturbance analyzers and disturbance monitors form a category of instruments that have been developed” for power quality work. It adds that “a number of different instruments are generally necessary” depending on what is being studied.
What to ask them to measure
The international measurement standard gives a useful checklist. The IEC webstore page for IEC 61000-4-30:2025, Power quality measurement methods, lists the parameters it considers, including “power frequency, magnitude of the supply voltage, flicker, supply voltage dips and swells, voltage interruptions,” “transient voltages, supply voltage unbalance, voltage harmonics and interharmonics, rapid voltage changes,” and “magnitude of current, harmonic currents,” among others. It says “all or a subset of the phenomena on this list can be measured,” so the scope should name the ones that matter for your problem.
Ask for current as well as voltage. Hydro One’s guide says “In order to characterize harmonic problems, it is critical to measure both voltages and currents.” Current also helps place the cause. Hioki’s article on power quality survey procedure says that when measuring at a receptacle, “If both voltage and current are falling, the cause can be traced to outside the building.” It adds: “If the voltage is falling, it can be assumed that a short circuit or inrush current caused the problem inside the building.”
Ask about neutral-to-ground voltage. The Dranetz HDPQ Quick Reference Guide says “Neutral to ground measurements are important, but optional,” and describes “using channel D as a differential input for measuring neutral to ground voltage” on a wye connection. Ask for it in writing if it is part of your concern.
| What to capture | What the documents say | What to ask for in the scope |
|---|---|---|
| Sags (dips), swells, interruptions | Hydro One: “Voltage sag refers to voltage drops below 90% of the nominal value (as per IEEE Std 1159 2009)” while the load still has power. | Event capture with RMS profile and waveform for each event |
| Transients | Hydro One: “Transient overvoltages and overcurrents are classified by peak magnitude, frequency, and duration”. | Confirm the instrument has a dedicated transient capture mode, and its sampling rate |
| Harmonics | Hydro One: measure both voltages and currents | Voltage and current harmonics, with the harmonic orders recorded |
| Flicker | IEC 61000-4-30 lists flicker as a measured parameter | Flicker logging, if lighting changes or rapidly changing loads are in question |
| Unbalance | IEC 61000-4-30 lists supply voltage unbalance and current unbalance | Voltage and current unbalance on three-phase services |
| Neutral-to-ground voltage | Dranetz: “Neutral to ground measurements are important, but optional.” | A neutral-to-ground channel, stated in the setup sheet |
Where to connect the recorder
Start close to the equipment that misbehaves. Hydro One’s guide says “it is advisable to begin monitoring as close as physically possible to the sensitive equipment being affected.” It also names a second spot: “The main service entrance is another important monitoring location,” because disturbances seen there can affect all equipment in the facility.
Two recording points can help separate causes. Hioki’s survey article says “Simultaneous measurements at a number of locations can help identify the cause of the problem.”
For harmonic questions, the service point has a specific role. The IEEE page for IEEE 519-2022, IEEE Standard for Harmonic Control in Electric Power Systems, says “The interface between sources and loads is described as the point of common coupling” and states “This standard addresses steady-state limitations.” If harmonic results will be compared with IEEE 519, ask where the point of common coupling is and whether the recorder was connected there.
Connections at a panel or service are live work for a qualified person. The Dranetz guide says “Connect the safety (earth) ground first, before making any other connections.” Ask how the connection was checked after setup. The same guide says “The phase angle display can also verify if monitoring connections have been made correctly.” Fluke’s 1736 and 1738 Three-Phase Power Quality Loggers page describes an “intelligent measurement verification function that allows you to reduce measurement errors.” A report should state that a check like this was done.
How long to record, and what triggers to set
There is no single correct duration. Hydro One says “The monitoring duration is dependent on the nature of the power quality problem being investigated.” For harmonics, levels “may need to be monitored for weeks, months, or even years to show the influence of load and seasonal variations.” For switching transients, “short term monitoring is all that is required.” The Dranetz guide says “The length of time to monitor a circuit can vary from a few hours to a few months or more depending on user application.” Record long enough to cover several occurrences of your problem.
Check that the instrument can hold that much data. Fluke’s 1736/1738 page gives a “Typical 10 logging sessions of 8 weeks with 1-minute intervals and 500 events.” It lists user-selectable averaging intervals from “1 sec” to “30 min.” Ask what interval was used, since short events need separate event capture rather than averages.
Thresholds decide what gets captured as an event. The Dranetz guide says “An event occurs when a programmed threshold limit is crossed,” and “Parameter thresholds are initially set based on the line voltage and current values that you enter.” That makes the nominal voltage setting important. The Dranetz HDPQ data sheet says “The instrument will configure itself using triggers based upon the IEEE 1159 +/- 10% of nominal recommendations.” Hydro One gives the better target: “The best approach for selecting thresholds is to match them with the specifications of the equipment that is affected.” If those specifications are not available, it suggests you “set the thresholds tight for a period of time,” then use the data to choose thresholds for longer monitoring. Give the equipment’s stated voltage tolerance to whoever sets up the recorder.
Instrument capability questions
Not every recorder captures every disturbance, so ask what the chosen instrument does. The IEC 61000-4-30:2025 page says “This document covers two classes of measurement methods (Class A and Class S),” and notes that “A” stands for “advanced” and “S” stands for “surveys.” Manufacturers state which class they claim. Fluke’s 1736/1738 page lists “IEC 61000-4-30 Class S.” Fluke’s 1770 Series Three-Phase Power Quality Analyzers page lists “IEC 61000-4-30 Class A.” The Dranetz data sheet says “Each Dranetz HDPQ product is Class A compliant with IEC 61000-4-30:2008.”
Transient capture differs the most between models. Fluke’s 1736/1738 page lists voltage “dips, swells, interruptions” and current “inrush,” but it does not list transient or flicker measurement. Fluke’s 1770 Series page gives transient sampling of “1775: 1 MS/s” and “1777: 1 MS/s, 20 MS/s” with a “±8 kV” range, and lists flicker to “IEC 61000-4-15 Class F1.” Hioki’s FAQ on transient and other event waveforms says the PQ3198/PW3198 “measures normal power quality items and transient overvoltage separately and differently.” If transients are your concern, confirm the model’s transient mode before the recorder goes in.
Ask about clock accuracy too. The Dranetz guide says “the time and date should be set to the proper timestamp before you begin monitoring.” Fluke’s 1770 Series page lists “GPS: < 1 ms absolute to UTC.” Accurate time lets you match events to your log. Whole-home surge protection is a separate topic and does not record what happened; see What Whole-Home Surge Protection Does, and Does Not, Protect.
Your log, and what the report should hand back
The recording is only half the evidence. Hydro One says “customers maintain a log detailing equipment problems that occur during the power quality monitoring,” and its Appendix B form includes date, time and “Equipment or Process Affected.” The guide says this “allows for the correlations of disturbances and system switching events with actual equipment power quality problems.” Hioki’s article puts it this way: “Knowing exactly what time the event occurred and when the trouble subsided” makes it easier to find the cause.
Software can produce standardized summaries. Fluke’s 1770 Series page says its software offers “One-touch reporting creates standardized reports conforming to standards like EN 50160, IEEE 519,” among others. A compliance summary does not replace an event list matched to your problem times. Hioki’s article recommends that you “Sort power quality events by specific dates and times, and cross-reference them with site information.”
| Report item | Why it matters | Red flag |
|---|---|---|
| Instrument make, model, stated IEC 61000-4-30 class | Shows what the recorder could and could not capture | No model named, or transients reported from a model with no transient mode |
| Connection points, wiring configuration, nominal voltage entered | Thresholds are based on the values entered | Wrong nominal voltage, or no record of a connection check |
| Start and end time, averaging interval, clock source | Shows whether the window covered your problem times | Recording ended before the problem recurred |
| Trigger thresholds for each event type | Hydro One recommends matching them to the affected equipment | Default settings with no explanation |
| Event list with time, magnitude, duration and waveform | Hioki notes event data gives “event magnitude, time, length and waveform shape” | Only averages or a pass/fail summary |
| Voltage and current trends, harmonics, unbalance, flicker, neutral-to-ground if scoped | Current trends help place the cause inside or outside the building | Voltage only, when harmonics or inrush are in question |
| Cross-reference to your equipment log | Links disturbances to actual equipment problems | No attempt to match events to logged problems |
Know the limits of this guide
This guide reads published documents. It does not interpret any recording or recommend an instrument. Product details come from manufacturer pages and may change. Standards pages were read for title, status and scope only. The full standards were not reviewed. Connecting a recorder inside a panel or at a service is energized work for a qualified electrician. Documents can change after November 17, 2026, so check current versions.
Primary references checked November 17, 2026: Hydro One, Power Quality Reference Guide for Customers and Utility Representatives; IEEE Standards Association, IEEE 1159-2019 IEEE Recommended Practice for Monitoring Electric Power Quality (standard page); IEEE Standards Association, IEEE 519-2022 IEEE Standard for Harmonic Control in Electric Power Systems (standard page); International Electrotechnical Commission, IEC 61000-4-30:2025 Power quality measurement methods (webstore page); Fluke, 1587 FC Insulation Tester Multimeter product page; Fluke, 1736 and 1738 Three-Phase Power Quality Loggers product page; Fluke, 1770 Series Three-Phase Power Quality Analyzers product page; Hioki, 4 Must-Know Tips for Conducting Power Quality Surveys article; Hioki, FAQ on transient and other event waveforms (PQ3198/PW3198); Dranetz, HDPQ data sheet; Dranetz, HDPQ Quick Reference Guide.
Frequently asked questions
My electrician measured normal voltage. Does that rule out a power quality problem?
Not for an intermittent problem. A spot reading shows the voltage only while it was measured. Catching sags, swells or transients that come and go needs a recorder left in place with event triggers set.
How long should a power quality recorder stay connected?
Hydro One says monitoring duration depends on the problem being investigated, and that harmonic levels may need weeks, months or longer. The Dranetz HDPQ guide says monitoring can run from a few hours to a few months or more.
Where should the recorder be connected?
Hydro One advises starting as close as possible to the affected equipment, and names the main service entrance as another important location. Hioki notes that simultaneous measurements at more than one location can help identify the cause.
What should I keep track of while the recorder is running?
Keep a log of each equipment problem with the date, time and the equipment or process affected. Hydro One recommends this log so disturbances can be matched with actual equipment problems.
Disclaimer: This guide is general information based on manufacturer, standards and utility documents, not professional electrical advice for a specific building or product. Connecting a power quality recorder is energized work for a qualified electrician; follow the instrument manual and safety instructions. Standards and product details may change. AI tools assisted with drafting. ClearTrade Report Editorial Team checked the cited sources and edited this guide.
Need a qualified professional?
Trusted Pros uses visible license-verification states and never ranks paid listings above unpaid listings.
