Both James Hardie fiber cement and LP SmartSide engineered wood warranties tie coverage to the manufacturer’s written instructions. The rules that matter most are hard to fix later: clearances from the ground, roofs, decks and gutters; how butt joints are gapped, flashed or sealed; nail type, placement and depth; how siding is stored and how cut edges are treated; and how soon primed siding is painted. For James Hardie, the product must also match the Hardie Zone (HZ5 or HZ10) where it is installed. Read the current documents before work starts.
Evidence label: Documentation-based guide. ClearTrade Report Editorial Team checked documents from James Hardie Building Products, LP Building Solutions (Louisiana-Pacific Corporation), ICC Evaluation Service (ICC-ES) and the Florida Building Commission product approval file on November 20, 2026. No outside professional review was performed and nothing was tested. Companies and products named are documentation examples, not recommendations. This guide contains no affiliate links.
Why the instructions decide warranty coverage
LP SmartSide. The LP SmartSide Prorated 50-Year Limited Warranty (form LPZB0523, dated 08/01/2025, for purchases on or after that date) conditions coverage on the product being “transported, stored, handled, installed, finished, and maintained in strict accordance with the Instructions.” Exclusions include “nailing or fastening not compliant with Instructions” and “failure to properly cut, prime, or paint the Product.” LP’s primed lap siding application instructions (form LPZB0515, 12/08/2023) state: “WARRANTY REMEDIES ARE NOT AVAILABLE IF THESE APPLICATION INSTRUCTIONS ARE NOT FOLLOWED.”
James Hardie. The Hardie Siding and Trim Express Limited Product Warranty (form HS2401, effective February 2024, covering HZ5 products including Hardie Plank HZ5 lap siding) runs “for a period of thirty (30) years.” Section 4(a) excludes damage from “failure to install the Product in compliance with applicable, published James Hardie installation instructions,” and “The improper storage, shipping, handling or installation of the Product.” The copy we read is hosted by a retailer (Lowe’s), not by James Hardie.
Claim deadlines also count. LP’s warranty says the owner “must notify LP Siding Warranty Services at 888-468-1417 within 30 days after discovering a condition” and before beginning any repair. The Hardie HS2401 warranty asks for written notice “within ninety (90) days after discovery of any claimed defect.”
Match the document to the product: HZ5, HZ10 and LP series
Hardie zones. James Hardie’s Hardie Zone System page says HZ5 “is right at home in climates with freezing temperatures,” and HZ10 is built for “areas with hurricane-force winds, salty sea air of the coast, and the brutal, humid heat of the south.” A 2010 HZ10 HardiePlank instruction filed with the Florida Building Commission states: “INSTALLATION OF HZ10® PRODUCTS OUTSIDE AN HZ10® LOCATION WILL VOID YOUR WARRANTY.” The December 2019 HZ10 edition tells installers to “CONFIRM YOU ARE USING THE CORRECT HARDIEZONE® PRODUCT INSTRUCTIONS.”
Evaluation reports. HardiePlank lap siding is covered by ICC-ES ESR-2290 (reissued March 2026, revised May 2026, subject to renewal March 2028). It says the siding “must be installed in accordance with this report and the manufacturer’s published installation instructions,” and that if they conflict, “this report governs.” LP SmartSide lap siding is covered by ESR-1301 (reissued February 2026, subject to renewal February 2028, hosted on lpcorp.com). It requires a copy of LP’s instructions on the job site. (ESR-1844 covers Hardie panel products, not HardiePlank.)
LP series. “38 Series lap siding may be attached direct to studs spaced max. 16 inches (406 mm) o.c.” and “76 Series lap siding may be attached direct to studs spaced max. 24 inches (610 mm) o.c.” ESR-1301 sets the same 16-inch and 24-inch maximums for its 3/8 and 7/16 Performance Category siding, though it does not name the 38 or 76 Series.
Clearances to ground, roofs, decks and gutters
- Ground. ESR-2290 says “A clear distance of 6 inches (152 mm) must be maintained between the siding and the earth.” LP’s instructions say “Min. 6 inch (152 mm) clearance must be maintained between siding and finish grade (ground cover).”
- Paved surfaces. ESR-2290 sets “not less than 2 inches (50.8 mm)” above paved surfaces in HZ5 areas and “not less than 1 inch (25.4 mm)” in HZ10 areas. LP says siding next to “porches, patios, balconies, or walking surfaces” needs “a clearance of at least 1 inch (25 mm) above horizontal surface,” with some listed exceptions.
- Roofs. LP: “Maintain 1 inch (25 mm) clearance between siding and roofing, or trim and roofing.” The 2010 Hardie HZ10 instruction says “Provide a 1″ – 2″ clearance between the roofing and the bottom edge of the siding and trim.” The 2019 edition shows clearances in figures, so check your edition.
- Flashing and gutters. The 2010 Hardie instruction says “Maintain a 1/4″ clearance between the bottom of James Hardie products and horizontal flashing” and “a minimum 1″ gap between gutter end caps and siding & trim.” LP: “Maintain 1 inch (25 mm) clearance between the end of the gutter and the adjoining wall.”
Roof clearances work with flashing and the drainage space behind siding. Our guide to rainscreens, drainage gaps and cladding compatibility explains how they fit together.
Butt joints, gaps and fastening
Butt joints. The two products handle the ends of boards differently. LP calls for a minimum 3/16 inch (5 mm) gap at butt joints and trim, and says to “caulk gap at butt joints with a high-quality exterior sealant meeting ASTM C920, min. Class 25.” With the flashing option on primed lap, “a min. 4 inch (102 mm) wide flashing is required.” The December 2019 HardiePlank HZ10 instructions say “Install planks in moderate contact at butt joints.” They add that “One or more of the following joint treatment options are required by code”: joint flashing (marked “James Hardie recommended”), caulking, or an “H” jointer cover.
Hardie fastening. The 2019 instructions say “Blind Nailing is the preferred method of installation for HardiePlank® lap siding products,” and face nailing “should only be used where required by code for high wind areas and must not be used in conjunction with Blind nailing.” The figures show a “min. 1 1/4 in. overlap” and “Nail 3/8 in. from edge of plank.” Studs may be “spaced a maximum of 24 in o.c.” On depth, it says “If setting the nail depth proves difficult, choose a setting that under drives the nail,” and “Fasteners must be corrosion resistant, galvanized, or stainless steel.”
LP fastening. LP says “Use a min. 0.092 inch shank diameter, hot-dip galvanized nail (ASTM A153) or equivalent” and to “Penetrate studs or combination of WSP sheathing and studs a min. of 1-1/2 inches (38 mm).” Nails go “3/8 inch (10 mm) from either end, and a min. of 3/4 inch (19 mm) from the top edge.” Courses overlap “a min. 1 inch (25 mm).” The nail head “should seat snug to face of siding, but not flush to distort the siding surface.” For blind nails, the only correction is re-nailing “when countersunk more than 1/8 inch.”
Storage, cutting and painting deadlines
Storage and handling. LP: “Store siding under a roof or separate waterproof covering” and “Store off the ground, supported on a flat well-drained surface.” Hardie’s 2019 instructions: “Store flat and keep dry and covered prior to installation” and “Carry planks on edge.”
Cutting. Hardie’s 2019 instructions say “DO NOT grind or cut with a power saw indoors” and “DO NOT dry sweep dust; use wet dust suppression or vacuum to collect dust.” For LP, the warranty-relevant rule is the cut edge: “Seal ALL exposed cuts of siding and trim,” and “Field spray applied coatings on cuts are not recommended.” ESR-1301 says that after field cuts, “all exposed surfaces must be finished according to the paint or caulk/sealant manufacturers’ specifications.”
Painting. LP: “Apply paint as soon as possible or within 180 days,” with 100% acrylic or oil paint. It says “DO NOT USE stain or vinyl-based paint.” Hardie’s 2019 HZ10 instructions say “Factory-primed James Hardie products must be painted within 180 days of installation.” The 2010 edition also gave 90 days for unprimed product.
| Rule | James Hardie HardiePlank (fiber cement) | LP SmartSide primed lap (engineered wood) |
|---|---|---|
| Ground clearance | 6 in. from earth (ESR-2290) | Min. 6 in. from finish grade |
| Paved or walking surfaces | 2 in. in HZ5 areas, 1 in. in HZ10 areas (ESR-2290) | At least 1 in.; 3/8 in. in listed cases |
| Butt joints | Moderate contact, plus joint flashing, caulk or H jointer (2019 HZ10) | Min. 3/16 in. gap, sealed, or joint moulding or flashing option |
| Nailing | Blind nailing preferred; 1 1/4 in. overlap; corrosion-resistant fasteners; under-drive if unsure | 0.092 in. hot-dip galvanized; 1-1/2 in. penetration; 1 in. overlap; snug, not flush enough to distort the surface |
| Stud spacing | Max. 24 in. o.c. | 38 Series 16 in.; 76 Series 24 in. |
| Primed paint deadline | Within 180 days of installation (2019 HZ10) | As soon as possible or within 180 days |
| Warranty claim notice | Written notice within 90 days (HS2401) | Notify within 30 days, before repair |
Know the limits of this guide
Nothing was tested and no installation was judged. The HardiePlank instructions we read are older HZ10 editions (December 2019 and November 2010) filed with the Florida Building Commission, because the jameshardie.com document library did not load for us. We found no current HZ5 instruction, so HZ5 rules come from ESR-2290. The Hardie warranty we read (HS2401, February 2024) is an HZ5 copy hosted by Lowe’s; we did not read an HZ10 warranty. Get the current version for your exact product, zone and purchase date from the manufacturer, and ask your code official which evaluation report applies.
Primary references checked November 20, 2026: LP Building Solutions, LP SmartSide Primed Lap Siding Application Instructions (LPZB0515, 12/08/2023); LP Building Solutions, LP SmartSide Prorated 50-Year Limited Warranty (LPZB0523, 08/01/2025); ICC-ES, ESR-1301 (reissued February 2026); ICC-ES, ESR-2290 (reissued March 2026, revised May 2026); James Hardie, HardiePlank Lap Siding installation instructions, HZ10 (HS11119, effective December 2019, Florida file FL13192 R7); James Hardie, HardiePlank installation instructions, HZ10 (effective November 2010, Florida file FL13192 R2); James Hardie, Express Limited Product Warranty, HZ5 (HS2401, February 2024, retailer-hosted copy); James Hardie, Hardie Zone System web page; ICC-ES, ESR-1844 CA Supplement (reissued November 2025, BuildSite copy).
Frequently asked questions
Can a siding warranty be voided by how the siding was installed?
Yes. LP's 50-year SmartSide warranty (LPZB0523, 08/01/2025) requires strict compliance with LP's instructions, and LP's lap siding instructions say warranty remedies are not available if they are not followed. James Hardie's February 2024 HZ5 warranty excludes damage from failure to follow its published installation instructions and applicable building codes.
What is the difference between Hardie HZ5 and HZ10 siding?
They are James Hardie product lines for different climates: HZ5 for freezing temperatures, snow and ice, and HZ10 for hot, humid and hurricane-prone areas. ICC-ES report ESR-2290 sets different clearances above paved surfaces: at least 2 inches in HZ5 areas and at least 1 inch in HZ10 areas. A 2010 HZ10 instruction says installing HZ10 products outside an HZ10 location will void the warranty.
How soon must primed siding be painted?
LP's primed lap siding instructions (LPZB0515, 12/08/2023) say to apply paint as soon as possible or within 180 days. The December 2019 HardiePlank HZ10 instructions filed in Florida say factory-primed James Hardie products must be painted within 180 days of installation.
Should butt joints in lap siding be gapped or tight?
It depends on the product. LP's primed lap instructions call for a minimum 3/16 inch gap at butt joints and trim, sealed or covered by a joint moulding or flashing option. The December 2019 HardiePlank HZ10 instructions say to install planks in moderate contact at butt joints and use a joint treatment such as joint flashing, caulking or an H jointer cover.
Disclaimer: This guide is general information based on manufacturer, government and standards documents, not professional siding, building code or legal advice for a specific home or system. Confirm current instructions and warranty terms with the manufacturer and code requirements with your local code official. Documents may change. AI tools assisted with drafting. ClearTrade Report Editorial Team checked the cited sources and edited this guide.
Need a qualified professional?
Trusted Pros uses visible license-verification states and never ranks paid listings above unpaid listings.
